ENQUIRE1 panel
01Bare 13.3″ E Ink panel
ED133UT3, 1600 × 1200, is a candidate in the Glider-supported panel family. Order the bare panel, without a third-party controller kit.
Confirm the exact variant, panel calibration, adapter pinout, firmware and case fit with Modos first. This supplier page is an enquiry, not verified stock.
Quote required
IDS · ED133UT3 enquiryMAKE / ENQUIRE1 populated board
02Glider controller mainboard
Request a tested standalone board from Modos. No standalone retail listing was verified. Alternatively fabricate and populate the open KiCad design through a PCB assembler.
The downloadable PCB is R1.3. A match between that revision and the case CAD has not been verified.
Quote required
Modos · request a loose boardMAKE / ENQUIRE1 populated board
03Matched panel adapter PCB
Request the matching adapter loose from Modos or manufacture it from the open design. Select connector population and routing for the exact panel. The downloadable Mega Adapter design is r0.1.
The source also contains other adapters. Do not assume the Mega Adapter and the adapter in the case CAD have identical mounting or dimensions.
Quote required
Adapter designs · manufacturing sourceSPECIFY1 matched ribbon
04Controller-to-adapter FFC ribbon
Obtain the separate board-to-adapter ribbon. The mainboard provides a 50-pin interface; confirm the correct pitch, length and contact-side orientation against both selected connectors.
A visually similar ribbon is not enough. The panel’s own flex tail is part of the panel and is not this cable.
Specification & quote required
Modos · request the cable specificationMAKE / ENQUIRE1 plate
05Internal support plate
Obtain the mid-frame as a separate item or fabricate to an approved drawing based on the original assembly. The complete STEP download contains its geometry.
Material, retention interfaces and manufacturing tolerances need approval before fabrication.
Drawing & quote required
Modos · request loose mounting hardwareSPECIFYPer approved module drawing
06Plate inserts, standoffs & board screws
Request these as loose pieces for the assembly experiment. The CAD contains insert geometry, but the case guide does not provide an order-ready specification for the internal mounting hardware.
Do not substitute the external M3/M4 case screws for internal board fasteners.
Specification & quote required
Modos · hardware specification enquirySPECIFYPer approved retention stack
07Panel retention & cushioning pieces
Obtain the exact retention pieces, pads or adhesive layers specified for the selected module. Request them separately, including installation drawings.
Material, thickness and placement are unresolved. The demo does not establish a safe bonding or clamping process.
Specification & quote required
Modos · panel mounting enquiryPRINT1 piece
08Front frame
Print Frame1.stl or order it from a printing service. The CAD frame spans approximately 302 × 230 mm; check the available build area and dimensional fit.
Quote required
Craftcloud · get a quotePRINT1 piece
09Back plate
Print Back Plate1.stl. Ask the printing service to preserve the mounting holes and countersinks. Follow the source guide’s shrinkage-compensation note.
Quote required
Craftcloud · get a quotePRINT1 piece
10Button strip
Print Button1.stl. The reference CAD uses one connected button strip. Check that the printed controls move freely.
Quote required
Craftcloud · get a quoteBUYAt least 5
11M4 × 5 mm flat-head screws
For mounting the module to the back plate. This listing is an A2 stainless, countersunk Pozi option matching the required diameter and length; confirm the head fits the case.
Use a matching Pozi bit. Do not substitute a longer screw: the guide warns of insert and screen damage.
Check supplier
TC Fixings · UKBUY14 screws
12M3 × 6 mm flat-head screws
For joining the back plate to the frame. A2 stainless Phillips countersunk listing, product SIK-M3-6-A2. Confirm the head seats correctly in your print.
The source guide corrects an older screw-length description to 6 mm. Use a matching Phillips bit.
Check supplier
Accu · UKIF NEEDED1 cable
13USB-C cable with video support
A USB-C cable specified for DisplayPort Alt Mode, such as USB31CC1M. With a compatible host port, the source guide supports one cable for video and power.
Reuse a suitable cable if you have one. For HDMI instead, the guide requires Mini-HDMI video plus USB-C power.
Check supplier
StarTech · USB31CC1M
DOWN TO THE COMPONENTSThe electronic parts inventory.
379 mainboard footprints (R1.3) and 16 Mega Adapter footprints (r0.1), extracted from KiCad. Each reference is one footprint; non-purchasable features and unpopulated options are included. Match these revisions to your build before using this list.
Loading inventory…
Links use supplier references recorded in the design; stock and substitutions are unverified. This is not a released purchasing BOM or machine placement file.